The differential assembly is of hypoid design with centerline of drive pinion gear set below centerline of ring gear. A collapsible spaer is used to set drive pinion bearing preload and all other differential adjustments are accomplished using shims. Stub axles transmit power out of differential, through independent rear suspension, to drive wheels. A clutch pack limited slip unit, "Powr-Lok", is available as an option.
Jaguar uses only one basic rear axle design, however, unit may not be fitted with a traction lock device. Also several different axle ratios are used. To determine axle ratio, divide number of ring gear teeth by number of pinion gear teeth. Whether or not axle is fitted with traction lock should be determined owner inquiry or test.
 |
| Fig. 1 Exploded view of Jaguar "Power-Lok" Differential Assembly |
4) If necessary, install oil seal track to half shaft splined flange, replace spacer. Thoroughly clean and de-grease splines of half shaft and bore of hub. Using a small brush sparingly apply Lactite "Stud Lock" to outer two thirds of half shaft splines. Assemble hub carrier to half shaft. Install washer and tighten hub carrier assembly nut. Install new cotter pin. Install dial indicator so it bears against hub and zero indicator. Using two levers, pry out on hub and measure hub bearing endfloat. If endfloat exceeds specifications, overhaul rear hub and carrier assembly. After installation of rear suspension in vehicle, check rear wheel camber.
STUB AXLE OIL SEAL
1) Remove half shaft. Remove locking wire and withdraw bolts securing brake caliper to final drive unit. Remove brake rotor, noting number of shims removed between rotor and stub axle flange. Remove lock wire and five bolts securing caliper mounting bracket. Withdraw drive shaft, together with caliper mounting shims, ball bearing and oil seal. Turn down tab washer and remove nut nut from stub axle. Remove ball bearing and caliper mounting bracket from stub axle.
2) Lightly oil seal and position carefully in final drive case. Press seal squarely and fully seat in case groove. Do NOT remove protruding portion of seal. Coat seal with hypoid oil and place caliper mounting bracket and seal assembly over stub axle. Slide ball bearing on drive shaft followed by new tab washer and nut. Ensure bearing seats square to stub axle shoulder and tighten nut. Turn up tab on washer.
3) Lightly oil stub axle splines and install shaft in final drive housing. Install bolts securing mounting bracket finger tight. Using feeler gauge, measure dimension between inside face of mounting bracket and final drive housing. The measurement obtained determines shim thickness required, and thinly coat mating faces and shims with suitable sealant (Hylomar). Tighten bolts in a diagonal sequence.
4) Wire lock securing bolts to tension in clockwise direction. Install brake rotors and half shaft flange, using shims removed from between rotor and flange. Install caliper on mounting bracket. Install suitable distance spacers (oversize nuts) to rotor studs and tighten nuts. Use feeler gauges to ensure that rotor is centrally located between jaws of caliper. If necessary add to or remove from shim pack between flange and disc to center rotor. Continue assembly in reverse of disassembly procedure.
PINION FLANGE AND SEAL
1) Disconnect propeller shaft. Check and record torque required to turn drive shaft flange clockwise (viewed from front) through backlash movement. Check rear wheels and remove flange securing nut and washer. Remove flange. Pry oil seal out of final drive case. Lightly score oil seal recess with tang of file.
2) Ensure oil seal recess is clean and free of oil. Lightly top new oil seal into recess ensuring seal is square with case. Reinstall flange, washer and nut. Tighten nut to 120 ft. lbs. (16.5 mkg) while rotating flange to ensure bearing seats correctly. Again check pinion preload. If preload is below specifications, continue tightening flange nut until specified preload is obtained. However, if preload exceeds maximum specified value, new collapsible spacer must be installed, see differential overhaul. Reconnect propeller shaft and remove wheel chocks.
FINAL DRIVE UNIT
1) Remove rear suspension assembly and drain final drive unit. Remove final drive mounting plate and shock absorber/spring units. Remove nuts securing half shaft inner universal joint to brake rotor and disconnect half shaft, noting shims removed. Remove nut from inner suspension arm fulcrum shaft and drift out shaft. Repeat for other side of unit. Disconnect and plug brake lines. Disconnect hand brake levers from compensator.
2) Remove locking wire from final drive mounting bolts, remove bolts and crossmember by tilting forward over pinion. Remove calipers from final drive unit. Remove brake rotors, noting number of shims removed from between rotor and stub axle flange. To install, reverse removal procedure making sure brake rotor is centered between jaws of caliper and wire lock tension bolts in clockwise direction.
OVERHAUL
 |
Fig. 2 Exploded View of Limited Slip
Differential Clutch Pack and Side
and Pinion Gears |
1) Remove rear cover and discard gasket. Remove lock wire and bolts securing caliper mounting bracket. Withdraw stub axle along with caliper mounting brracket shims, ball bearing and oil seal. Turn down tab washer and remove nut, ball bearing and caliper mounting bracket from stub axle. Repeat procedure fro second stub axle. Remove bolts securing differential bearing caps and lift off caps. Pry out differential assembly using two levers and taking care not to damage housing.
2) Remove drive pinion nut and washer. Mark relative positions of flange and pinion and remove flange. Using a suitable press, remove pinion from differential housing. Remove oil seal, oil thrower and outer bearing cone. Examine inner and outer bearing cups fro wear. If replacement is required, extract cups using suitable tools (SL.14 and SL. 14/1). NOTE - If removal of bearing cups is difficult, gently heat final drive housing in rear of bearing caps. On "Powr-Lok" differentials only, proceed as follows:
3) Remove differential side bearings using suitable tools (SL.14 and 14/3). If no reference marks are present, scribe a line across both halves of differential case to ensure correct reassembly. Remove bolts securing both halves of differential case. Split case and remove clutch discs and plates from one side. Remove differential side ring, pinion side gear and pinion cross shafts complete with gears. Remove remaining side gear and ring and extract remaining clutch discs and plates.
4) On non "Powr-Lok" differential only, remove peening and drift pinion shaft lock pin out of carrier. Remove gears, shaft and shims from carrier.
REASSEMBLY AND ADJUSTMENT
 |
| Fig. 3 Measuring Side Bearing Preload |
Case Assembly - 1) On "Powr-Lok" differentials, install clutch plates and disc alternately into flange half of case. Installtwo belleville clutch plates so that convex sides are against case. Install side ring and position one side gear into ring recess. Install cross shafts. Install pinion cross shafts complete with pinion gears ensuring that ramps on shafts coincide with mating ramps in case.
2) Assemble differential case halves ensuring that reference marks are lined up and clutch friction plate tongues are aligned with grooves in differential case. Install bolts but do not tighten yet. Check alignment of splines by inserting both stub axles. Tighten differential case bolts with stub axles in position. With one stub axle locked, other axle must not turn more than .75" (19 mm) measured on a 6" (152 mm) radius.
3) On non "Powr-Lok" differentials, install pinion shaft, shims and gears into differential carrier. Secure lock pin by peening.
Side Bearing Preload - Install differential side bearing without shims, on differential case, making sure that bearing and housing are perfectly clean. Place differential assembly in housing. Install dial indicator with indicator leg against back face of ring gear. Using sutiable pry bars between housing and bearing cups, move differential assembly fully to one side of housing. Zero dial indicator and move assembly to other side. Record indicator reading and add .009" (.20 mm) to reading to give total shim pack required. Remove differential assembly from housing.
 |
Fig. 4 Measuring Drive Pinion
Gear Installed Depth |
Drive Pinion Depth - 1) Place pinion, together with inner bearing cone, into housing. Turn housing over and support pinion. Install pinion outer bearing cone, flange, washer and nut, omitting collapsible spacer, oil slinger and oil seal, tighten nut. Using suitable dial indicator support fixture (SL3), zero dial indicator on setting block (4.H.A.). Place dial indicator fixture firmly on face of pinion and not indicator reading to bottom of housing bearing bore (see illustration).
2) The indicator reading shows deviation of pinion setting from zero cone setting. This value agree with value etched on face of pinion at bottom. For example, if value etched on pinion is -2, dial indicator should read -.002". If setting is incorrect, dismantle pinion and remove pinion inner bearing cup. Add or remove shims as required, reassemble and recheck pinion depth.
3) When setting is correct, extract pinion fro housing sufficiently far to remove outer bearing cone. Install collapsible spacer to pinion ensuring that it seats firmly on machined shoulder of pinion. Insert pinion into housing, install outer bearing cone, oil slinger and oil seal. Lightly grease splines of pinion shaft and install flange. Install new washer on end of pinion with convex side facing end of shat. Install but DO NOT tighten nut.
Backlash Adjustment - 1) Place differential assembly complete with side bearings but less shims, in housing. Ensure that bearings and housing are perfectly clean. Install dial indicator on housing with feeler on back face of ring gear. Pry differential case and ring gear assembly away from pinion until opposite side bearing is seated against housing. Zero dial indicator at this point.
2) Move differential assembly towards pinion until ring gear is deeply meshed with pinion. Note indicator reading and from this value, subtract the backlash allowance etched on drive gear (eg B/L.007 dones .007"). This result will yield the thickness of shims (in inches) to be placed between differential case and side bearing on ring gear side of differential. Install this thickness of shims (in inches) to be placed between differential case and side bearing on ring gear side of differential. Install this thickness of shims, taking shims from pack determined previously under "Side Bearing Preload". Install balance of total shims required on opposite side of case. An example of calculations required follows
EXAMPLE:
 |
Fig. 5 Measuring to Determine Ring Gear
Side Shim Thickness |
Side Bearing Preload Reading..................... .080"
PLUS Preload Value................................. .009"
Total Shim Pack....................................... .089"
Pinion-to-Ring Gear Clearance................... .042"
MINUS Etched Backlash Value.................. .007"
Total Ring Gear Side Shims....................... .035"
Total Shim Pack....................................... .089"
MINUS Ring Gear Side Shims................... .035"
Opposite Ring Gear Shim Pack.................. .050"
3) With shims calculated installed, lower differential assembly into position, lightly tapping bearings home with a soft hammer. Make sure ring and pinion gears mesh as installation proceeds. Install side bearing cups, ensure proper cup is placed in proper bearing. Tighten cup bolts. Mount dial indicator on housing with feeler against back face of ring gear. Turn pinion by hand and check ring gear run out. If run out exceeds specifications, disassemble differential, clean all mounting surfaces and check for burns.
 |
Fig. 6 Measuring Ring Gear-to-Drive Pinion
Gear Backlash |
4) Now place dial indicator to measure ring gear backlash. Move ring gear and check that backlash is to specifications, transfer necessary shims from side of differential case to the other. NOTE - To increase backlash, remove shims from ring gear side and install on opposite side and vise versa. Finally run a gear tooth contact pattern and adjust shims as necessary.
Pinion Bearing Preload - Install pinion and stub axle of seals. Install stub axles following procedure given under stub axle removal and installation. Tighten flange nut to specified torque. During tightening process rotate flange to ensure correct seating of taper roller bearings. Use care not to over tighten nut. if nut is overtightened, install a new collapsible spacer as pinion bearing preload will otherwise be incorrect. Install final drive rear cover using new gasket and suitable sealer (Hylomar).
